Pager4 v6:
- Programming software version: 6.0.2
- Firmware version: 6.0.5
The programming software contains the following bug fixes:
- The Cloud IP address and port can be edited in the programming software again, so that the proxy servers can be configured.
- Filename extension was missing when saving the settings
- Czech translation support
- The programming software did not read back the settings if the Windows local settings were not in the Hungarian region
- After factory reset, reading the settings got stuck
- Despite device lock, the administrator was able to do a factory reset, as programming software lock could be disabled.
The firmware contains the following bug fixes:
- SIA protocol: the sequence counter started from 0, cannot take the value 0
- It made a mistake when reporting events (repeated or omitted), now corrected
- The event exit delay did not work after factory reset, now corrected
- Waiting for the phone by starting the EG91 modem (the device did not start at longer boot time)
- Direct IP connection: Adapter did not allow reconnection
Main version 7 of Pager4 contains the following new functions and bug fixes:
New functions of the programming software:
- Possibility to set WiFi SSID manually
- Displaying WiFi chip firmware version in status
- Possibility to limit the number of signal transmission in voice call and SMS
- Integration of AT logging option in the programming software
- Possibility to select the GSM network operator
- Possibility to omit current date in SMS notifications (It is needed in SMS command sent to another module.)
- By the abortion of operation write, the programming software does not try again, but indicates the error instead
- The settings belonging to the service events were migrated from the general menu to the tab service events, making the general menu more transparent
- The options that are not supported by the device hardware are not displayed in network selection (e. g. the 2G module is with 3G and 4G networks not compatible)
- MVP.Next server support has been implemented in the product
- Blocked events are marked in the event log
- The date format set in the programming software prevails in the time stamps of notifications, too
- Possibility to set SMS command forwarding
- Possibility to limit outgoing calls
- Introduction of the event Daily SMS limit
- In module status information, network and data connection types are displayed in the more common formats of 2G/3G/4G, too
- Differentiating GSM and GPRS data connections in module status information
- Implementation of other environmental variables and further information in logging, allowing easier debugging
- Displaying all data in module status information in case of remote access, too
- Possibility to import Pager4 settings into Pager4 PRO
- Possibility to edit the TELL Cloud IP address and port has been implemented in advanced settings
- Possibility to query SIM card balance via GSM call
Bug fixes of the programming software:
- Blocking multiple programming software running parallel
- Correction of the data volume calculator: correction of data traffic limit value and data rounding unit scale
- Correction of remote programming error via TEX protocol
- Retaining channel selection setting in the system log
- Correction of WiFi handling, preventing the previously set access point to be stuck, that is why only one WiFi access can be set
- Deleting affected events when changing arming mode after a warning question
- By arming / disarming on input events, you cannot set any input events on the input that is reserved for this
- Termination of voice message option in case of WiFi version
- Correction of localization errors of the programming software
- Possibility to delete multiple phone numbers
- After deleting phone numbers for sending SMS, the previously set actions that use this phone number will be deactivated by the programming software. It speeds up action performance.
- Changes had been saved even when pressing the button Cancel when changing the limit for data use
- The SIM card could be unlocked by remote access even without access right
- Factory reset could be performed by remote access even without access right
- Increasing the length of event names
- The module register did not load the access data by TEX or direct connection
- GSM/GPRS/3G errors appeared among the service events of WiFi modules
- Correction of configuration saving and reload error
- Correction of output control by status change
- It was not possible to configure rights in the menu Admin rights
- Possibility to configure the parameters for the service event incoming call
- By arming mode with toggle switch a wrong warning message referring to another input was displayed
- Buttons arming/disarming had been inactive until reading back the settings
- Correction of decimal point error in case of low supply voltage level and supply voltage restore
- In the service events dialog, only 1 output was displayed, for the product version IN4.R2, too
- The software did not provide the file with a file extension when saving the settings
- The programming software ran in English at installation even after selecting the German language
- In case of a non-Hungarian region, the programming software did not read back the settings
- Correction of the deletion of the given WiFi access point
New functions of the firmware:
- Possibility to select the GSM network operator
- Possibility to limit the number of signal transmission in call and SMS
- Modification of handling the RTC (real-time clock) chip (handling different hardware types)
- Possibility to set SMS command forwarding
- Possibility to limit outgoing calls
- Outgoing call counter and related warning service events
- Introduction of the event Daily SMS limit
- Forwarding GSM modem type to the programming software, allowing it to display only options that match the modem type when selecting a network
Bug fixes of the firmware:
- Correct handling of WiFi SSID names containing spaces
- After setting a wrong WiFi password, it was not possible to connect to another access point
- Increasing the length of event names
- After updating from firmware version 6, firmware version 7 did not start with the 6-input hardware
- Correction of the error of duplicated APPIDs of the mobile application
- In case of an outgoing call, correction of the error of the last try, correct handling of the call counter
- Termination of the option for producing sound recordings from GSM voice calls (the sound was recorded in bad quality due to the bad call quality)
- Correction of WiFi handling, avoiding the previously set access point to get stuck. Thus, only the WiFi access can be set.
- Exit delay was configured as restore event among service events in factory default settings